How to Install Tile Edging

Raw tile edges chip. That’s the whole reason edging exists, and it’s the first thing we check on any shower or backsplash walkthrough where the last row of tile just stops against open air. A clean edge piece closes that exposed cut face, stops water from wicking into it, and turns a DIY-looking job into one that reads as finished from across the room.

Homeowners usually come to this question mid-project, tile already ordered, sometimes already partway up the wall. Pick a trim type, get the sequencing right since some go in before the tile and some after, and don’t rush the corner cuts.

What This Detail Actually Does

Three jobs, not one. Protection comes first, since a bare cut edge on ceramic or porcelain chips on contact with a dropped shampoo bottle or a vacuum bumper in a way a finished edge never does. Waterproofing comes second, closing the porous cut face where water would otherwise sit against raw material. Appearance matters least structurally, yet it’s what clients notice first. A tiled niche with a mitred or bullnose edge looks like a finished detail. Raw grey cut tile edge looks like the job stopped early.

Skip the edging on a shower niche or an outside corner and the tile still works for a while. It fails first exactly where water sits longest, the worst possible place for that to happen.

The Main Types of Tile Edge Trim

Bullnose, pencil, metal profile: those three cover most residential jobs, and each one solves a slightly different problem.

Bullnose tile is a regular tile with one rounded factory edge, made to match the field tile in colour and finish. It installs exactly like a normal tile, thinset on the back, pressed into place, which makes it the easiest option for anyone doing a first tile project. Not every tile line offers a matching bullnose piece, and that’s the catch. Check availability before committing to a pattern if a rounded edge is the look you’re after.

Pencil liner is a narrow, elongated strip, usually 3/8 to 1/2 inch wide, often used to frame a backsplash or cap a half-height wainscot. It reads as a decorative accent more than a structural edge, and it shifts around in wet thinset more than a full-size tile does because there’s so little surface area gripping the wall. We pull excess mortar from around a pencil piece immediately, not as a cleanup step later, for exactly that reason.

Schluter, or whatever the shop label calls the metal profile, sits in a different category entirely. It’s the only one of the three that goes in before the last row of tile, not after. The piece’s flat “leg” gets embedded in thinset first, then the final tile row gets set on top of it, with only the narrow finished edge showing once the job is done. Skip that order and there’s no clean way to add metal profile onto an already-finished edge. That mistake gets made more than people expect.

Caulk earns a mention too, though it’s not really edging at all. On tumbled stone, glass, or anything with a naturally clean cut face, a bead of colour-matched caulk along the exposed line does the job without adding a physical piece. Cheapest option on the list, and the right call more often than most DIY guides admit.

Tools and Materials You’ll Need

Thinset mortar, a notched trowel, a margin trowel, spacers, a bucket of clean water with a sponge: that covers the wet work for bullnose and pencil. Add a wet saw for cutting those two pieces cleanly, and a miter box with a hacksaw for cutting Schluter-style metal trim, since a spinning blade near thin edging is a real way to send a piece flying across the bathroom.

Matching trim thickness to the tile matters more than most first-timers realize. A 10mm tile sitting on a layer of thinset needs a piece closer to 11 or 12mm to sit flush once everything’s set, not something measured to the tile’s bare spec alone. Confirm that number before buying.

How to Install Tile Edging Step by Step

Bullnose and pencil both go in after most of the field tile is set and cut to fit the last exposed edge.

Skim-coat thinset onto the back of the piece and onto the wall section it’s going into. Notch the wall coat so the ridges run parallel to the tile’s shortest edge, then press it firmly into place. Wipe the surface clean with a damp sponge before the thinset skins over, and set spacers to hold a consistent grout line against the neighbouring field tile. On pencil liner specifically, scrape excess mortar away right away rather than waiting, since the small surface area means it shifts if left sitting too long.

Metal profile runs in reverse order. The leg goes into thinset on the wall first, pressed and worked back and forth until mortar comes through the cutouts on its face. Then thinset goes onto the back of the final tile, extra applied specifically where the profile sits underneath, and that last row gets pressed into place over the embedded leg. Get this backwards, tile first and edging second, and there’s genuinely no clean fix short of pulling that row back out.

Grout closes out any of the three options. Let the thinset cure fully first, usually 24 hours, before grouting the joint between the edge piece and field tile the same way you’d grout anywhere else.

Adding Edging After the Tile Is Already Up

Depends entirely on which type. Bullnose and pencil, yes, without much fuss, since both install the same way regardless of when the surrounding tile went in. We do this all the time on older bathrooms where the original install left a raw edge exposed for years and the homeowner finally wants it finished.

Metal profile is the one that doesn’t retrofit cleanly. It’s designed to sit under the last tile row, embedded before that tile goes on, and pressing it against an already-finished edge afterward doesn’t hold the same way. The workaround on an existing installation is usually a surface-mount trim made for retrofits, sitting over the finished edge instead of under it, or pulling the last row and redoing that section properly. Neither is a five-minute fix, worth knowing before choosing metal on a fresh job you might want to modify later.

Where These Installs Go Wrong

Mismatched thickness tops the list. A trim piece ordered to the tile’s bare spec sheet number, ignoring the thinset layer underneath, sits proud or recessed once everything’s set, and that gap shows from across the room under the wrong light.

Wrong sequencing on Schluter-style metal profile is second, the mistake we get called to fix most on other contractors’ jobs. Tile goes in first, then the piece gets pressed against a finished edge, and it never sits flush because it wasn’t designed to be installed that way.

Grout haze on the surface is a smaller but constant annoyance, especially on textured metal finishes where dried residue sits in the texture and won’t wipe off with a sponge alone. A grout haze remover and a soft brush handle it, applied before the residue fully cures if possible.

Loose pencil liner shows up a year or two after install more than any other failure. Small surface area, not enough thinset coverage on the back, and it works itself loose from vibration and temperature swings over time. Full mortar coverage during install, not a couple of dabs, is the fix that prevents the callback.

Is This a DIY Job?

Bullnose and pencil, realistically yes, if you’re already comfortable with the tile install itself. Both pieces go in the same way as any other tile, and a wet saw rental plus a Saturday afternoon covers most single-room jobs.

Metal profile is where DIY confidence should drop a notch. Sequencing has to be right the first time, cutting requires a steady hand with a hacksaw or the piece distorts, and there’s no forgiving fix once the last tile row is set over a poorly placed leg. It’s not a hard skill to learn. Getting it right on the one attempt most homeowners get, before the tile above it is committed, is the harder part.

Corners and returns are the other place DIY jobs go sideways, mitred cuts at 45 degrees needing to land tight with no gap. Practice on scrap first. If there’s anything unusual going on underneath the room you’re planning, talk to us before you buy.

Frequently Asked Questions

What is the best way to finish tile edges?

Bullnose for a matching, low-fuss finish. Metal profile for a clean modern line, installed before the last tile row, not after. Caulk on tiles with a naturally finished cut edge, tumbled stone and glass mostly, where a physical piece isn’t needed at all.

Can I install tile edging myself?

Bullnose and pencil, yes, for anyone already comfortable tiling. Metal profile is less forgiving since the sequencing and cuts have to be right the first time, with no easy fix once the final tile row is set.

Can you add tile edge trim after tiling?

Bullnose and pencil, yes, any time. The metal option needs to go in before the last row, so adding it after usually means a surface-mount retrofit piece or pulling that section of tile back out.

What are the common problems with tile edge trim?

A piece ordered to the wrong thickness for the thinset bed underneath, metal profile installed in the wrong order, grout haze stuck in textured finishes, and pencil liner working loose from thin mortar coverage on the back.

Small piece, big job, and it’s usually the detail that decides whether an install reads finished or not. Get the sequencing right on metal profile before the last tile goes up, match thickness to the actual thinset bed, and the rest is patience with a wet saw. Our wall tile installation jobs across Nanaimo, Parksville, and Campbell River carry this detailing as a standard line item, not an upsell, because a raw edge left exposed is the kind of thing a homeowner notices every day for years.

Related Questions

• How to Attach Tile Edging?
• How Do You Tile a Bathroom?
• Can You Install Tile Over Laminate Flooring?
• Can You Tile Over Cork Floor?
• Are Large Tiles Harder to Install?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Can Tile Grout Be Replaced?

Yes. Tile grout can be replaced, and it doesn’t have to mean touching the tile itself. Old grout comes out, new grout goes back in, same tile stays exactly where it is. What trips people up isn’t whether it’s possible. It’s whether their situation actually calls for a simple regrout or something bigger underneath.

The Short Answer

Cracked, stained, crumbling, or missing grout is almost always replaceable without pulling a single tile. The grout lines get cleared out, cleaned, and repacked with fresh grout. A bathroom floor or shower surround can go from tired-looking to brand new in a weekend without a demo crew anywhere near it.

The exception is grout failing because of what’s happening underneath it, not the grout itself. Loose or hollow-sounding tile, a floor that flexes, or grout that keeps failing in the same spot within a year of a redo: that’s a substrate problem wearing a grout costume. Replacing the grout again just resets the clock.

Signs Your Grout Actually Needs Replacing

Not every ugly grout line needs a full tear-out. Some respond to a deep clean and a coat of sealer. Cracking through the joint, chunks missing between tiles, and black mold that keeps coming back after cleaning are the three signs that mean cleaning won’t cut it anymore.

Run a fingernail along a grout line. Crumbles or comes away in your hand, that’s cement grout that’s past its working life. Stays firm but just looks dingy, a cleaning pass and a sealer probably solves it. Mold that returns within weeks of scrubbing usually means water’s getting behind the grout, not just sitting on top of it, which points at replacement rather than another round of bleach.

Can You Grout Over Old Grout?

Sometimes, but it’s not our first move. Epoxy grout can go directly over sound cement grout once the old surface is struck down a couple of millimetres to give the epoxy something to bite into. That saves a step, and it works fine when the old grout is intact and just needs a refresh in colour or finish.

It’s a different story when the old grout is cracked, hollow, or already pulling away from the tile edge. Grouting over a compromised joint just buries the problem under a fresh layer that fails again on the same timeline. Full removal costs more time up front. It’s also the only way to know what’s actually going on with the tile edges and the substrate before sealing it back up.

How Grout Replacement Actually Works

Old grout comes out first, whether that’s a manual grout saw on a small job or an oscillating tool with a grout removal blade on anything bigger. Depth matters more than most homeowners expect. At least a third of the joint’s thickness needs to come out for the new grout to bond properly, and on grout that’s already failing, we take it closer to two-thirds or all the way to the substrate.

Once the old grout is gone, the joints get vacuumed and wiped clean. No dust, no debris, nothing sitting between the tile edges that’ll weaken the new bond. New grout goes in, gets packed tight with a float, and the excess comes off the tile face before it sets. Then it’s a haze cleanup over the next day or two, and a cure window before the area sees water again.

Coastal Air Slows the Clock Down

Central Vancouver Island doesn’t get the bone-dry winter air that speeds curing along in a lot of the country. Grout and thinset both cure by losing moisture, and that process takes longer when the ambient humidity is already high for eight months of the year. A cure window that reads 24 to 48 hours on the bag can run a day longer than that in a Campbell River or Courtenay bathroom in January.

Rushing water back onto fresh grout in a damp climate is the single fastest way to weaken it before it’s even had a chance to set properly. We build the extra day into the schedule rather than pretend the label applies exactly the same way here as it does somewhere drier. On the plus side, the Island’s soft municipal water means less mineral scale building up in grout lines over time than homeowners moving here from somewhere like Alberta tend to expect.

Is Replacing Grout Worth It?

For a bathroom or kitchen that’s structurally sound and just showing its age in the grout lines, yes, almost every time. Fresh grout changes how a whole room reads, often more than a new tile would, at a fraction of the cost and mess of a re-tile.

It stops being worth it the moment the grout is failing because tile is loose, a floor is flexing, or water has already gotten past the grout and into the substrate. Regrouting a shower with a soft spot underneath it looks great for a few months and then fails again in the exact same place. That’s when the real fix is a proper look at what’s under the tile, not another tube of grout.

DIY Regrout or Call In a Pro

A single section, a small bathroom, or a floor with no signs of movement is a reasonable weekend project for a homeowner comfortable with basic tools. The work is tedious more than difficult. Slow, steady removal, a clean joint, and patience during the haze cleanup get most DIY jobs across the line.

Full showers, anything with hollow-sounding tile, or a grout job that’s already failed once tend to go sideways fast without the right read on what’s causing it. We get called in most often after a DIY regrout held for a season and then cracked again in the same spot, which usually means the real cause never got addressed the first time around.

What It Actually Costs

Materials for a DIY regrout on a standard bathroom run modest, a bag of grout, a removal tool, a float and sponge. Labour changes that math once a pro’s doing the work, and the range moves with square footage, whether it’s epoxy or cement grout, and how much of the old material has to come out before the new goes in.

The bigger cost swing isn’t grout versus grout. It’s a straightforward regrout versus a job that turns into pulling tile because the substrate underneath needs attention first. Get a look at it before assuming either direction, since the grout on the surface doesn’t always tell the whole story about what’s happening underneath it.

Frequently Asked Questions

Can you put new grout over old grout?

With epoxy grout and sound old grout underneath it, yes, after striking the surface down a couple of millimetres. Cracked or hollow old grout needs to come out fully first, or the new layer just fails on the same schedule.

Is it easy to replace tile grout?

More tedious than technical. Removing the old grout without chipping tile edges takes patience and a light touch, especially around corners. Most homeowners who take their time get through a small job without trouble.

How much does it cost to replace tile grout?

DIY materials for a standard bathroom stay modest. Professional replacement scales with square footage, grout type, and how much removal the job needs before new grout goes in. A quick look at the space is the only way to get a real number instead of a guess.

Is replacing grout worth it?

Yes, when the tile and substrate underneath are sound. Not worth it as a repeat fix if the same spot keeps failing, since that points to a problem the grout alone can’t solve.

Not sure if your grout needs a simple refresh or if something underneath is driving the problem? We look at plenty of these on bathroom tile and floor tile jobs across Campbell River, Courtenay, and Comox. Get in touch and we’ll tell you straight which one you’re dealing with.

Related Questions

• What Is the Best Grout for Tile?
• Can One Tile Be Replaced?
• How to Grout Tile Backsplash?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

How to Fix Chipped Tile?

A two-part epoxy filler, colour-matched and cured overnight, closes most small chips for good. That is the short version of how to fix chipped tile, and it covers roughly nine out of ten calls where the damage stops at the surface glaze. The other one in ten needs the tile pulled and swapped, and knowing which situation is in front of you before buying a repair kit saves a wasted Saturday.

Chips and cracks get treated as the same problem online. They are not. A chip is missing material, a small crater bitten out of the glaze or the tile body. Crack means something else: material still there, just split through. Different depth, different repair, and mixing up which one is on the floor is the most common reason a DIY fix looks patchy again within a season.

Chipped Tile vs Cracked Tile: What’s Actually Different

Glaze-only damage sits in the top coating, the shiny layer fired over ceramic or porcelain body. Fill it with a colour-matched epoxy and, from three feet back, it disappears. Body chips go past that coating into the clay or porcelain underneath, and colour match gets harder since the body rarely matches the surface finish exactly, especially on a printed or textured tile.

Hairline cracks read as their own category, usually from an impact or a subfloor that shifted slightly under the tile. Structurally most are fine to fill and leave. Cosmetically they get worse the longer they sit, since grime and moisture work into the line and darken it. Catch one early, before it has had a winter to collect dirt, and the fix is a fraction of the work.

Why Tiles Crack or Chip in the First Place

A dropped pan or a dragged appliance leg accounts for most chips. Cracks trace back further, usually to something under the tile rather than the tile itself. Bad installation is the biggest one: adhesive that never covered the full back of the tile leaves hollow spots, and a hollow spot under load is where a crack starts. A cracked or flexing subfloor does the same thing from underneath.

Vancouver Island adds its own version of this. A damp crawlspace under an older Nanaimo or Victoria home lets the wood subfloor swell and shrink with the seasons, and a tile set without a movement joint or flexible thinset takes that stress directly. Homes with in-floor heat do something similar from the opposite direction, expanding the substrate every time the system cycles on, so a crack that shows up in spring often started moving months earlier.

Tools and Materials for a DIY Tile Chip Repair

A two-part epoxy filler made for tile, not general-purpose wood filler, is the core of the kit. Painter’s tape to mask the surrounding glaze, a small mixing tray, a plastic spreader or old gift card, fine sandpaper for levelling once cured, and a rag for cleanup round it out. Colour-matching pigment or a pre-tinted kit saves guessing, since mixing custom colour by eye rarely lands on the first try.

Skip anything marketed as an instant super glue fix. It bonds fast and looks fine for a week, then shrinks and pulls away from the edges once it dries fully, leaving a visible seam that is harder to fix the second time than the original chip was.

How to Fix a Chipped Tile Step by Step

Clean the chip first. Dust, old caulk residue, or soap scum in the crater stops epoxy from bonding properly, and that is the single biggest reason a repair fails within weeks. A quick wipe with rubbing alcohol and a dry cloth handles most of it.

Mask the tile edge with painter’s tape, mix the epoxy in small batches (it sets faster than expected once combined), and press it into the chip with the spreader, slightly overfilled rather than flush. Overfilling gives room to sand back level once cured; underfilling leaves a dip that catches light and shows.

Match colour before it fully cures, not after. Most kits give a short working window to tint and blend the surface before the epoxy sets hard, and that window is the only real chance to feather the edge into the surrounding glaze. Let it cure fully, usually 24 hours, then sand lightly with fine paper and wipe clean.

How to Fix a Hairline Crack in Tile

Same epoxy, different technique. A hairline crack needs the filler worked into the line itself rather than built up on top, since any excess sitting proud of the surface catches light and draws the eye straight to it. Fine applicator tip or a toothpick works the epoxy along the crack, then a clean cloth pulls the excess off the surface before it sets.

Disguising a crack that cannot be filled invisibly, usually on patterned or heavily veined tile, comes down to colour blending rather than a perfect match. Tinted epoxy mixed slightly darker than the tile, worked only into the line, reads as a natural vein or grout shadow instead of a repair. A perfectly matched crack repair, oddly, often stands out more than one that blends into the tile’s existing pattern.

Can a Cracked Tile Be Repaired, or Does It Need Replacing?

Depth is the deciding factor. A crack confined to the glaze or a chip under the size of a dime almost always fills and holds. Full-width cracks are the opposite signal, especially one that moves slightly underfoot or that keeps reappearing after a fill: the substrate underneath is still shifting. Filling that tile again and again just delays the same repair.

Full replacement also wins when the tile sits somewhere the crack traps moisture, a shower floor or a backsplash behind a sink. A hairline crack there is not just cosmetic; it is a path for water into the substrate, and that turns a five-dollar epoxy fix into a much bigger job a year later if it is ignored.

What to Fill a Chipped Tile With

Two-part epoxy is what holds up. It bonds to ceramic, porcelain, and most natural stone, cures hard enough to walk on, and takes tint well for colour matching. Acrylic caulk and spackle both get suggested online and both fail the same way: too soft, they dent under normal foot traffic and pull away from the edge within a season.

Porcelain repair kits marketed specifically for the material tend to include a slightly different resin blend built to match porcelain’s harder, denser surface. Worth the few extra dollars over a generic ceramic kit if the floor is porcelain, which most new-build kitchens and bathrooms on the Island are.

Touching Up Chipped Porcelain

Porcelain chips differently than ceramic. The colour runs through the full body on through-body porcelain, so a small chip barely shows since the material underneath nearly matches the surface. Glazed porcelain behaves more like ceramic: the visible layer is a thin coating, and a chip through it exposes a lighter body underneath that needs full colour matching, not just a clear filler.

Test the epoxy tint on a spare tile or an inconspicuous corner before committing to the visible chip. Porcelain’s surface sheen varies by finish, matte, polished, or textured, and a colour match that looks right in the tray can still read wrong once it is sitting under kitchen lighting.

Will Home Insurance Cover a Cracked Tile?

Almost never on its own. A cracked tile from normal wear, a dropped pot, or age gets treated as maintenance, the same category as a worn faucet or a scratched countertop. Coverage only tends to kick in when the crack is a symptom of a covered event, a burst pipe that shifted the subfloor, for instance, and even then the adjuster is paying for the underlying damage, not the tile itself.

When to Call a Tile Pro Instead of DIY

A single chip or hairline crack on a floor or backsplash is a Saturday-afternoon fix for most homeowners willing to follow the steps above. Multiple cracked tiles across one area, a crack that keeps returning after a fill, or any crack near a shower pan or tub surround is where we would stop the DIY route and take a proper look underneath. What looks like one bad tile sometimes turns out to be a substrate problem working its way to the surface, one tile at a time.

A floor tile installation or ceramic tile installation quote covers both the swap and a check of whatever is underneath, since replacing one cracked tile without knowing why it cracked usually means doing it again in a year. Every room has its own version of this, so talk to us about yours.

Frequently Asked Questions

Can chipped tile be repaired?

In most cases. Small glaze chips and hairline cracks fill with a colour-matched two-part epoxy and hold for years. Deep body damage or a crack that keeps reopening usually means the tile needs to come out instead.

How do you fix cracked tile without replacing it?

Clean the crack, work tinted epoxy into the line with a fine applicator, wipe the excess before it cures, then let it set for 24 hours before walking on it. The technique stays the same whether the crack is on a floor or a wall.

Is it common for ceramic tile to crack?

More common than manufacturers advertise, mostly from installation shortcuts rather than a weak tile. A hollow spot in the adhesive, a missing movement joint, or a subfloor that flexes under load accounts for most of the cracks we get called out for.

How much are Sid Dickens tiles worth?

Different product entirely. Sid Dickens Memory Blocks are decorative ceramic art pieces, not structural floor or wall tile, and their resale value runs through collector and auction markets rather than a tile installer’s price list. Worth checking with a dealer or auction house for current pricing instead of a contractor.

Most chipped tile fixes come down to patience more than skill: clean the surface, match the colour before the epoxy sets, and let it cure the full 24 hours instead of rushing back onto the floor. A quote for bathroom tile installation or a straight tile swap is worth getting once a crack keeps reappearing, since that pattern almost always points to something moving underneath rather than a bad piece of tile.

Related Questions

• Are Tiles Worth It?
• Why Does Tile Crack After Installation?
• How Much for a Tile Cutter?
• Are Tile Leveling Systems Worth It?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Are Ceramic Tiles Good? What They Get Right and Where They Fall Short

Yes, for most rooms in a house. Ceramic tile has been the default flooring and wall choice for kitchens and bathrooms for a reason: it’s affordable, it comes in more colours and patterns than almost anything else on the market, and it holds up to normal household life without much fuss. Where it starts to lose ground is water-heavy spots and anywhere a dropped pot or dumbbell is a real risk. Worth breaking down before picking it for a specific room.

How Good Is Ceramic Tile, Really?

Durability is the first question every homeowner asks. Good, not indestructible, is the real answer. Ceramic is fired clay with a glazed top surface, and that glaze is what does the real work against scratches, stains, and moisture. A well-installed ceramic floor in a normal household kitchen or hallway will run 15 to 20 years before it looks tired, longer in a low-traffic bathroom.

Water resistance comes almost entirely from the glaze, not the tile body underneath. Crack that glaze, chip a corner, and the porous clay under it is exposed. That’s the failure mode we see on older ceramic floors: not the field tile wearing out evenly, but one chipped corner near a doorway that eventually lets moisture in and stains the grout around it.

Maintenance is where ceramic genuinely earns its reputation. A damp mop and a mild cleaner handle it. No sealing required, unlike natural stone, and no waxing, unlike older vinyl composition tile. Design range is the other real win: glazed ceramic ships in more colours, patterns, and finishes than porcelain does, since the glaze sits as its own printed layer rather than running through the whole tile body.

Ceramic also comes out ahead on the environmental side, something buyers rarely ask about but worth mentioning. It’s made from natural clay, sand, and water, fired without the additional chemical binders some flooring materials need, and a lot of manufacturers now run recycled content through the mix. Long lifespan factors in here too. A tile that lasts 15 to 20 years and never needs replacing beats almost any “green” flooring product replaced every decade.

Disadvantages of Ceramic Tile

Cold underfoot and hard on anything dropped. Those are the two complaints that come up most on site walk-throughs, and neither one is a defect, just physics. Clay tile doesn’t hold heat, and it doesn’t give. A dropped glass breaks. Drop a cast iron pan and it can crack the tile itself, not just the glass.

Installation gets tricky on anything but a flat, stable subfloor. Ceramic doesn’t flex, so a subfloor with any bounce or unevenness telegraphs straight through to cracked tiles or grout lines within a year or two. That’s the single most common callback we get on ceramic jobs that weren’t installed by a tile crew: not the tile failing, the substrate underneath it moving. Older Vancouver Island homes with plank subfloors and no cement backer board over top are where we see this most, and it’s almost always fixable with proper prep before the tile ever goes down.

Uniformity is a smaller gripe but a real one for design-forward homeowners. Because glaze prints as a separate layer, edge chips on ceramic reveal a different-coloured clay body underneath, which shows more than a chip on through-body porcelain does. It rarely matters day to day, but shows up more on a light-coloured floor near an entryway where chips are more likely in the first place.

Slippery when wet is real on glossy finishes, and it catches people off guard in entryways and bathrooms. A matte or textured glaze solves most of it. Chip resistance also loses to porcelain in high-traffic commercial-style settings, though a typical residential floor rarely sees that kind of abuse.

Are Porcelain Tiles Good for Bathroom Floors?

Better than ceramic, on paper and in practice. Porcelain is fired at a higher temperature from a denser clay blend, which gives it a lower water absorption rate: under 0.5% for true porcelain versus 3% to 7% for standard ceramic. On a bathroom floor, where standing water and constant humidity are the norm, that lower absorption matters more than almost any other spec.

Density also means porcelain resists chipping and scratching better than ceramic does, which counts for something in a bathroom that doubles as a laundry room drop zone or gets a curling iron dropped on it more often than anyone admits. Cost runs 20% to 30% higher than comparable ceramic, and that premium buys real performance in this specific room rather than a marketing bump.

Finish still matters more than material here. A glossy porcelain floor gets just as slippery wet as glossy ceramic. Matte, textured, or small-format mosaic with more grout lines for grip: pick one of those regardless of which material wins the durability argument.

Are Porcelain Tiles Good for Bathroom Walls Too?

Walls are a different equation, and ceramic often makes more sense there. Almost no foot traffic and close to no abrasion happen on a wall, so porcelain’s extra density buys very little. Ceramic wins on price and on design range, subway tile, zellige, handmade-look finishes ship as ceramic first almost every time.

Porcelain still has a place on walls: large-format panels that read as a single slab, or a shower wall that needs to match a porcelain floor for a seamless look. Outside of those two cases, ceramic on the walls and porcelain on the floor is the split we install most often across bathrooms on Vancouver Island.

Can Porcelain Tile Be Used on Floors Elsewhere in the House?

Kitchens, entryways, mudrooms, basements: porcelain handles all of them well, and in a few of those rooms it’s the smarter call over ceramic. A kitchen floor takes dropped cans, cast iron, and grit tracked in from outside. Porcelain’s density holds up to that better over a 15-plus year lifespan than ceramic does.

Basements are where porcelain’s low absorption really pays off. Concrete slabs below grade wick moisture, sometimes constantly, and a tile that shrugs off water contact is worth the extra cost in that one room even when budget is tight everywhere else. Outdoor and unheated applications, covered porches, garage mudrooms, need a frost-rated porcelain specifically. Not every porcelain tile on a showroom floor is rated for freeze-thaw, and that’s a question worth asking before buying, not after.

Radiant floor heating is another spot porcelain edges ahead. It transfers heat slightly better than ceramic and handles the expansion and contraction of a heating cycle with less risk of hairline cracking over the years.

Ceramic vs Porcelain: Which Should You Actually Pick?

Budget and traffic answer most of this question before design even enters the conversation. Low-traffic rooms, guest bathroom walls, a powder room floor that sees light use: ceramic does the job at a lower price point and gives more design flexibility. Wet floors, high-traffic zones, anywhere below grade: porcelain’s density and water resistance earn the extra cost.

Most of the homes we work in across Nanaimo, Parksville, and Campbell River end up mixing both rather than picking one for the entire project. Ceramic on bathroom walls and a powder room floor, porcelain in the primary bathroom and kitchen. That split gets the design range where it doesn’t cost anything in performance, and the durability where it actually matters.

What Does Ceramic Tile Cost Compared to Porcelain?

Ceramic runs roughly $2 to $8 per square foot for material on a standard residential job, with mid-range options landing around $4 to $5. Porcelain sits at $3 to $12, and that gap widens fast once you get into large-format or wood-look porcelain planks, which can push past $10 a square foot before installation.

Installation labour tells a bigger story than material price alone. Porcelain is denser and harder to cut, which means slower work and more blade wear on a wet saw, and that shows up as a higher labour line on any quote from a real tile crew. On a typical bathroom floor, expect porcelain to add 15% to 25% to total installed cost over an equivalent ceramic job, materials and labour combined.

Where that math flips: large-format tile. Fewer, bigger pieces mean fewer cuts and faster coverage per hour, so a big-format porcelain floor can sometimes install for close to the same price as smaller-format ceramic, even with the higher material cost per square foot. Worth asking any quote to break out material versus labour before assuming porcelain always costs more to have installed. We quote this kind of work from Campbell River down through Courtenay and Comox, so get in touch if you’re nearby.

Frequently Asked Questions

What are the disadvantages of ceramic tile?

Cold and hard underfoot, prone to chipping if something heavy drops on it, and slippery when the finish is glossy. None of those rule it out. They just mean picking the right finish and installing it on a solid subfloor.

How many years do ceramic tiles last?

15 to 20 years is typical for a well-installed residential floor, sometimes longer in low-traffic rooms. Cracked grout or a chipped corner usually shows up first, long before the tile field itself wears out.

What is better for a bathroom floor, porcelain or ceramic tile?

Porcelain, mainly for the lower water absorption. Ceramic still works fine in a low-humidity powder room, but a primary bathroom that sees daily shower steam favours porcelain’s density.

Is porcelain or ceramic tile better for bathroom walls?

Ceramic, in most cases. Walls don’t get the foot traffic or standing water that make porcelain’s extra durability worth the price, and ceramic’s colour and pattern range is wider.

What is the disadvantage of porcelain tile flooring?

Cost sits 20% to 30% above ceramic for comparable options, it’s heavier and harder to cut on site, and installation labour runs higher because of both. Same slip risk as ceramic on a glossy finish.

What tiles should not be used on a shower floor?

Anything with a glossy, polished finish, regardless of ceramic or porcelain. Matte or textured tile in a smaller format gives feet something to grip. Our floor tile installation page covers slip-rated options room by room.

Can mold grow under porcelain tile?

Not under the tile itself if the install was done right, since porcelain barely absorbs water. It can grow in the grout lines or at a failed seam where water gets past the surface and sits against the substrate underneath.

Ceramic and porcelain both earn their keep, just in different rooms. The mistake we see most isn’t picking the wrong material outright, it’s picking one finish for the whole house and hoping it performs the same in a mudroom as it does on a bedroom-adjacent bathroom wall. Room-by-room is the right way to make the call, and it’s usually a quick one once traffic and moisture are on the table.

Related Questions

• Can Tiles Fall Off Walls?
• Can Mosaic Tiles Be Used on Floors?
• Are Tile Countertops Making a Comeback?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Are Bigger Tiles Better for Shower Walls?

Usually. Fewer grout lines, a cleaner sightline, a shower that reads bigger than it measures. That’s the upside in three words. Everything underneath the tile has to be flatter and straighter than it does for a small tile job, though, and that catch costs more than most homeowners budget for.

The Short Answer

Bigger tile on a shower wall looks better in almost every case we install it. Less grout means less visual clutter and less cleaning, and a shower wrapped in one continuous surface pulls the eye up and out instead of stopping at every grout line. That’s the design win, and it’s real.

What it doesn’t do is forgive a crooked wall. Studs out of plumb by a quarter inch disappear under 4×4 tile. Under a 24×48 panel, that same quarter inch shows as a visible wave across the whole wall. We’ve walked into 1970s Nanaimo bathrooms where the framing hadn’t been touched since the house went up, and the first conversation isn’t about tile size, it’s about what the wall needs before any tile goes anywhere near it.

What Counts as “Bigger” for a Shower Wall

Anything over 12×12 gets called large format in the trade. In practice, the shower walls we tile most often land in three brackets: 12×24 as the entry point, 16×32 or similar for a step up in visual impact, and 24×48 panels for a client chasing the most seamless look possible. Past 24×48, you’re into slab territory, and that’s a different install method entirely, not just a bigger version of the same job.

Is 12×24 Tile Too Big for a Shower?

No, and it’s not close. 12×24 is the single most common shower wall size we set on the Island, full stop. It’s large enough to cut the grout lines roughly in half compared to a 12×12, small enough that an out-of-plumb stud doesn’t turn into a visible lippage problem, and forgiving enough for a first-time large-format install. If you’re weighing tile size for a shower and want the safest upgrade from standard subway or 12×12, this is it.

Why Bigger Tile Reads Better in a Shower

Fewer seams. That’s the entire mechanism, and everything else follows from it. A 12×12 tile on an 8-foot shower wall needs roughly twice the grout lines a 12×24 needs, and each one is a thin dark line breaking up the surface. Stack enough of them and the eye reads a grid instead of a wall. Pull half of them out and the eye reads a surface instead.

Light plays into it too. Larger format tile, especially anything with a polished or semi-polished finish, bounces more light across an unbroken plane. Small bathrooms without a window benefit the most here, since that reflected light is doing real work making the room feel less closed in. We’ve had clients genuinely surprised at how much bigger a shower feels after going from 12×12 subway to 12×24 on the same footprint, same fixtures, same square footage.

Do Larger Tiles Make a Bathroom Look Bigger?

Yes, through fewer grout lines and better light reflection, not through any actual change in square footage. The room measures the same before and after. What changes is how much visual interruption the eye has to process, and less interruption reads as more space. Pair large format tile with a light grout close to the tile colour and the effect compounds, since the grout lines stop registering as a separate element entirely.

It’s worth saying the effect has a ceiling. A tiny powder room shower stall wrapped in 24×48 panels can look like it’s trying too hard, tile bigger than the space that’s holding it. Match the scale of the tile to the scale of the room, not just to the trend.

What Bigger Tile Actually Costs

Material first. Large format porcelain typically runs 15 to 40 percent more per square foot than standard 12×12, depending on finish and where it’s sourced. That range is wide because slab-look porcelain at the top end costs a lot more than a basic 12×24 field tile.

Labour is where the bigger jump happens. A skilled installer needs more time per tile: back-buttering, checking level constantly, using leveling clips to control lippage, and working alone or with a helper on anything over 16 inches since one person can’t safely set a wet 24×48 panel solo. On a standard shower surround, we typically quote large-format wall tile at 25 to 40 percent more labour than the same square footage in 12×12. That gap narrows on a bigger job since the fixed setup costs spread out, but it never disappears.

The Installation Trade-offs Nobody Mentions

Wall flatness is the big one, covered above, but it’s not the only one.

Corners and niches eat large tile fast. A shower niche cut into a wall of 24×48 tile means every piece touching that opening gets custom cut, and a bad cut on a $12-a-square-foot tile costs a lot more than the same mistake on $3 subway. Plumbing valve cutouts work the same way: precise, unforgiving, and expensive to redo.

Weight matters more than people expect. Porcelain slab tile is heavy, and a wall needs proper backer board and, past a certain size, mechanical support while the thinset cures. Gravity pulls on wet-set large tile in a way it doesn’t on something the size of a coaster.

Handling breakage is the quiet cost. A cracked 12×12 is a minor loss, replaced from the box already on site. Crack a 24×48 panel instead, especially a patterned or textured run that’s back-ordered, and the job can stall for weeks waiting on a replacement. We order an extra 10 to 15 percent overage on large-format runs specifically for that reason, higher than the 8 to 10 percent we’d carry on standard tile.

What Are the Disadvantages of Large Tile?

Higher material and labour cost, less forgiveness for an out-of-plumb wall, harder and more expensive cuts around niches and fixtures, more breakage risk in transport and handling, and fewer hands who can install it well. Every one of those is manageable with the right prep and the right installer. None of them disappear just because the tile looks great in the showroom.

Mixing Big Tile With Small Tile in the Same Shower

Most of the best-looking showers we build don’t use one tile size everywhere. Large format on the field walls, a mosaic accent in the niche or on a shelf, sometimes a contrasting band at eye level. It gives the eye something to land on without breaking the overall seamless feel, and it lets a client use a pricier accent tile in a small dose instead of tiling the whole shower in it.

Glass shower doors, or none at all, help the mix read as intentional rather than busy. A clear sight line into the shower shows off the accent without a shower curtain chopping the view in half. Framed doors and heavy curtains work against a large-format install, since they hide the exact feature the bigger tile was meant to show off.

Layout pattern matters more with large tile than small. Straight-stack (grid) reads calmer and more modern than a staggered brick pattern, which was originally developed to hide the natural size variation in older tile stock. Vertical stacking on a shower wall can visually stretch a low ceiling. Horizontal runs do the opposite, widening a narrow stall. Match the grout colour tight to the tile and the pattern nearly disappears, which is usually the goal on a large-format job in the first place.

When Smaller Tile Still Wins

Shower floors, almost always. Small format tile, mosaic sheets especially, gives you far more grout lines for traction and lets the floor slope properly to the drain. A large tile on a sloped shower pan either needs custom cutting to follow the slope or sits proud in the middle, and neither is a good outcome.

Tight or oddly shaped showers push the same direction. A shower stall with three walls under five feet and an awkward corner niche generates so many cuts on large format tile that the material savings from fewer pieces gets eaten by waste and labour anyway. Budget-driven jobs land here too. Not every bathroom needs the large-format upgrade, and a well-set 12×12 or subway pattern with tight grout lines still looks sharp.

Older Island homes with lath-and-plaster walls or settled framing sometimes make the decision for you. Getting a wall flat enough for 24×48 tile can mean an extra day of backer prep that a homeowner wasn’t planning to pay for. At that point the recommendation is 12×24, not the biggest tile on the shelf.

What We’d Actually Recommend

For most Vancouver Island bathrooms, 12×24 on the shower walls is the sweet spot: enough size reduction in grout lines to notice, forgiving enough for real-world framing, and priced within reach of most renovation budgets. Reserve 16×32 and up for a wall you know is flat, or one you’re willing to pay to make flat.

Not sure what your existing framing can handle, or planning a full bathroom tile installation? Worth checking the walls before picking a tile size off a showroom sample. Most of our wall tile jobs start with exactly that walk-through. Anyone weighing this up around Campbell River, Courtenay or Comox can ask us and get a real number.

Frequently Asked Questions

What is the best size tile for shower walls?

12×24 for most homes. Large enough to cut grout lines noticeably, small enough to forgive a wall that isn’t perfectly flat. 16×32 or larger works well once you know the wall behind the tile is straight.

Is 12×24 tile too big for a shower?

No. It’s the most common shower wall size installed today, a genuine step up from 12×12 without the flatness demands or handling risk of anything over 16 inches.

What are the disadvantages of large tiles?

Higher material and labour cost, less tolerance for an out-of-plumb wall, pricier custom cuts around niches and fixtures, and more breakage risk than a standard-size tile.

Do larger tiles make a bathroom look bigger?

They make it feel bigger through fewer grout lines and more reflected light, not through any change in actual square footage. The effect works best when tile size is matched to the room, not maxed out regardless of scale.

Related Questions

• Are Tile Countertops a Good Idea?
• Are Wall Tiles and Floor Tiles the Same?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Should I Back Butter Floor Tiles?

Depends on the tile. Anything past 15 inches on a side, natural stone, or a tile with a deep waffle pattern stamped into the back: back butter it. Standard ceramic or small-format porcelain, set with the right trowel and correct technique underneath, doesn’t strictly need it. Back buttering isn’t a universal rule. It’s a fix for specific problems, and most floor jobs run into at least one of them.

What Back Buttering Actually Does

A thin coat of mortar spread across the back of the tile with the flat side of the trowel, before the tile ever touches the ribbed bed on the floor. That’s the whole technique. Three things happen once it’s there.

Bond strength goes up first. Pressing mortar into the tile’s back keys it in, and installers call this “burning” or “keying in” for a reason: it locks the two surfaces together instead of just resting on top. Second, it fills the waffle pattern most tile backs are stamped with at the factory, flattening what would otherwise be tiny air pockets. Third, and this one gets skipped over: it fills warpage. Tile isn’t perfectly flat off the pallet, and back buttering takes up slack a stiff trowel bed can’t reach on its own.

When Floor Tiles Actually Need It

Large-format is where the debate ends. Past roughly 15 inches on the long edge, most manufacturers and installers stop treating back buttering as optional. Natural stone works the same way. The industry handbook that governs coverage standards calls for back-buttering, or “back parging,” on stone tile in every application, no exceptions carved out for small pieces or dry rooms.

Uncalibrated or bowed backs push the same direction. A tile that rocks slightly on a flat surface before it’s even set needs the extra mortar layer to take up that warp, or the corners lift while the middle rides high on the substrate. We check for this by setting a straightedge across the back of a sample tile before the job starts. If it doesn’t sit flat, back buttering goes on the plan regardless of size.

Do I Need to Back Butter 12×24 Floor Tile?

Yes, in most cases. A 12×24 sits right at the edge most manufacturers use to define large-format, and on a floor that edge gets treated conservatively. Foot traffic and furniture load a floor tile in ways a wall tile never sees, so the coverage requirement climbs before size even enters the conversation. We back-butter every 12×24 or larger floor tile on our jobs, full stop, no case-by-case judgment call needed on that one.

What Happens If You Skip It

Hollow spots first. Tap a tile that needed back-buttering and didn’t get it, and you’ll hear the difference: a flat thud instead of a solid knock. That’s a void under the surface, and voids don’t heal themselves once the mortar cures.

Corners crack next, usually months later, not on install day. A void near a corner or edge concentrates whatever load lands on that spot, and porcelain doesn’t flex to absorb it the way a wood floor would. We get called to jobs, not ours, where a beautiful floor develops a spiderweb crack in one specific tile for no obvious reason. Pull that tile and there’s almost always a dry patch where the back should have been buttered and wasn’t.

Lippage shows up too, on tiles that were warped and never got the extra mortar to compensate. The edges don’t sit level with the neighbouring tile, and that’s a trip hazard as much as it’s an eyesore.

How Much Mortar Coverage You Actually Need

80 percent for most interior floors. 95 percent for anything exterior, in a shower, or under heavy commercial traffic. That’s the industry standard, and it’s checked by pulling tiles back up, not by eyeballing the trowel ridges before you set them.

Back buttering on its own doesn’t hit those numbers. Trowel notch size matched to the tile, ribs run in one direction, tiles slid perpendicular across those ribs to collapse them: that combination is what actually produces coverage. Skip the technique and coat the backs anyway, and a floor can still land under 80 percent.

Trowel and Mortar Matter Almost as Much

Back buttering gets the attention, but the trowel notch does most of the actual work. Too small a notch on a large tile, and there isn’t enough mortar in the ribs to reach full coverage no matter how carefully the back was coated. Match the notch to the tile: a quarter-by-quarter-by-quarter square notch handles most standard ceramic, while anything approaching 12×24 or bigger wants something closer to half-inch, and true large-format slabs push that further still.

Mortar type shifts too. Standard thin-set works fine for ceramic and small porcelain. Large-format porcelain and natural stone usually call for a large-format or medium-bed mortar, built with more polymer to hold that extra weight without slumping before it cures. Using a standard mortar under a heavy 24×24 tile is a common shortcut that shows up later as the same voids and lippage a skipped step causes, even when the tile backs were coated correctly.

How to Check Your Own Coverage

Pull one tile early in the job. Set it, wait a few minutes, then lift it back off before the mortar sets and look at the back. Solid grey coverage across most of the surface is what you want. Patchy islands of mortar with bare tile between them mean the notch size, mortar consistency, or technique needs adjusting before the rest of the floor goes down. Do this once at the start, then again partway through if the tile size or substrate changes anywhere in the room.

Frequently Asked Questions

Should you always back butter tiles?

No. Small and mid-size ceramic or porcelain with correct trowel technique often meets coverage standards without it. Large-format, natural stone, and anything warped or uncalibrated: back butter those every time.

What happens if you don’t back butter floor tiles?

Voids form under the tile where it needed the extra mortar and didn’t get it. Those voids show up later as hollow-sounding spots, cracked corners under load, or lippage on tiles that were slightly warped to begin with.

Do I back butter floor tile?

Under 15 inches, ceramic or porcelain, flat on the back, and trowel technique already hitting 80 percent coverage: skip it. Anything larger, stone, or warped: back butter it.

Do I need to back butter 12×24 floor tile?

Yes. 12×24 sits at the size where most manufacturers start calling it large-format, and floor traffic loads that tile harder than a wall ever would. We treat it as a back-butter tile without exception.

When to Bring in a Pro

A hollow tile you can’t safely replace without risking the ones around it, a floor already showing cracked corners, or a large-format job where the coverage math has to be right the first time: that’s where we tell homeowners to call rather than gamble on a DIY reset. Standard ceramic on a straightforward floor tile installation is well within reach for most homeowners who follow the steps above. Large-format porcelain tile and natural stone are where the margin for error gets thin fast, and a redo costs more than the hour it would have taken to get the coverage right the first time. Cheaper to get a quote up front than to price a repair later.

Related Questions

• Can I Tile My Garage Floor?
• What Sticks Tile to Floor?
• Can Peel and Stick Floor Tiles Be Removed?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Can I Mix Tile Adhesive with Cement?

No, not really, and the short version is worth saying plainly before the longer explanation. Tile adhesive comes pre-formulated with polymers and additives that give it flexibility and bond strength cement mortar never had. Add cement to the bucket and that formulation gets disrupted, not improved. We get this question often enough on jobs across Campbell River and Courtenay that it’s worth walking through why, not just stating the answer.

What Tile Adhesive and Cement Actually Are

Cement mortar is the old-school approach: cement, sand, and water, mixed on site in a ratio the installer has to get right every batch. Tile adhesive is a manufactured, ready-to-use product, cement-based in most cases but engineered with polymers, binders, and additives that control flexibility, open time, and moisture resistance. Same base ingredient, completely different result once the chemists get involved.

That’s the part homeowners miss. Tile adhesive isn’t cement with better marketing. It’s cement that’s had the variability engineered out of it, tuned for a specific substrate and tile type before it ever reaches the bucket.

Why Contractors Add Cement Anyway

Cost drives most of it. Tile adhesive runs more per bag than plain cement, so bulking out a mix with cement stretches the bag further. Some installers also grew up mixing mortar the traditional way and never fully trusted the bagged stuff. Neither reason holds up once you look at what the mix actually does under a tile.

What Happens When Cement Goes Into the Mix

Flexibility drops first. Tile adhesive is built to absorb small movements, thermal expansion, minor substrate shifts, without cracking loose. Cement is rigid by comparison, and adding it stiffens the whole mix past what it was designed to tolerate. Tiles set in a cement-diluted adhesive are more prone to hairline cracking or slow detachment, the kind of failure that doesn’t show up for a year or two.

Bonding strength suffers next. The polymers in tile adhesive are what grip the tile face and the substrate at the same time. Dilute that ratio with cement and the bond gets weaker at exactly the interface that matters most. Curing time shifts too, usually unevenly, since cement sets on its own schedule that has nothing to do with the adhesive’s engineered open time. A batch can end up too fast in one corner of the bucket and too slow in another.

The One Place This Argument Gets Murky

A few tile adhesive manufacturers market blending their product with cement as a way to boost durability and “rock cement strength” on tough substrates. That claim shows up in vendor literature more than it shows up on our actual jobsites. Manufactured adhesive already accounts for substrate and tile type in its formulation. Adding cement back in undoes the engineering the manufacturer already did. We haven’t seen a job where it made the bond better. We’ve seen a few where it made the bond unpredictable.

Will Tile Adhesive Bond to Concrete?

Yes, and this is where tile adhesive earns its price tag. Concrete is exactly the kind of substrate tile adhesive is formulated to grip, provided the slab is clean, cured, and free of sealers or curing compounds that block adhesion. A new concrete pour needs roughly 28 days to cure before tile goes down on it. Skip that wait and moisture trapped in the slab works against the bond regardless of what adhesive sits on top.

Mixing It Properly: Hand vs Power Mixer

Small residential jobs, a backsplash or a bathroom floor, often get mixed by hand with a margin trowel, and that works fine at that scale. Anything larger runs into the same problem every mixing-equipment manufacturer flags: hand mixing struggles to break up lumps and tends to trap air bubbles that weaken the cured bond. A low-speed, high-torque drill paddle solves both problems. High-speed drills do the opposite, whipping air into the mix and overheating the motor in the process.

Water goes into the bucket first, then the adhesive gets added slowly, then it gets mixed until smooth with no dry pockets at the bottom. Let it sit a few minutes, called slaking, then give it a second short mix before spreading. Skipping the rest period is a common shortcut that shows up later as pinholes in the cured adhesive bed.

Vancouver Island’s Damp Climate Changes the Timeline

Coastal air here runs humid roughly eight months of the year, and that changes how a mixed batch behaves compared to a drier inland climate. Damp air slows both thinset and grout curing, sometimes by a noticeable margin on an unheated job site in December. Batches that would set in an hour inland can run closer to ninety minutes here, which means smaller mixed batches and closer attention to a tile’s working time before it skins over. Cutting corners on the mix ratio to speed things up, adding cement being one version of that shortcut, backfires faster in this climate than it would somewhere drier.

A proper floor tile installation accounts for that cure-time math before the first bag gets opened, adjusting batch size and open time to the day’s humidity rather than a generic label instruction written for a different climate.

Which Tile Types Need Which Adhesive

Ceramic tile tolerates a standard thinset without much fuss. Porcelain, being denser and less absorbent, usually wants a modified adhesive with stronger polymer content to get a full bond across a tile that doesn’t pull moisture from the mix the way ceramic does. Large-format tile and natural stone push that requirement further still. None of that changes if cement gets added to the bucket; it just makes an already-tight tolerance tighter. A ceramic tile installation quote will usually specify adhesive type up front for exactly this reason.

Frequently Asked Questions

What to use to mix tile adhesive?

Water first, adhesive second, added slowly and mixed until smooth. Hand mixing with a margin trowel works for small jobs. Anything bigger calls for a low-speed, high-torque drill paddle, since a standard high-speed drill whips air into the batch and weakens the cured bond.

Which is stronger, tile adhesive or cement?

Tile adhesive, for its actual job. Plain cement mortar can be stronger in raw compressive strength, but tile adhesive is engineered for flexibility and bond at the tile-substrate interface, which is the strength that actually matters for a floor or wall that needs to stay down.

Will tile adhesive bond to concrete?

Yes, once the slab is clean, cured, and free of sealers. New concrete needs about 28 days before tile goes down, otherwise trapped moisture in the slab undermines the bond no matter how good the adhesive is.

Does sticky tile stick to cement?

Peel-and-stick vinyl tile bonds poorly to bare cement or concrete long term. The surface needs to be fully cured, dust-free, and often primed first. Even then, peel-and-stick is a short-term solution on a porous substrate, not a permanent one.

Cost pressure is the real reason this question keeps coming up, more than confusion about what the two products are. Skip the shortcut. A bag of proper adhesive costs less than the callback. Questions about which adhesive fits a specific tile or substrate, get in touch and we’ll sort it out before anything gets mixed.

Related Questions

• How to Remove Cement from Bathroom Tiles?
• How to Install Vinyl Floor Tiles with Adhesive?
• Can You Use Construction Adhesive for Tile?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Can I Use Porcelain Tile Outdoors?

Yes, porcelain tile is one of the best materials for a Vancouver Island patio. Not every porcelain tile, though. That distinction trips up more homeowners than any other part of an outdoor tile job.

The Short Answer

Purpose-built outdoor porcelain tile handles Island winters, pool decks, and driveways without much complaint. Standard indoor porcelain, pulled from a leftover box in the garage, does not. The difference comes down to three things: how much water the tile absorbs, how thick it is, and how the surface grips a wet boot. Nail those three and porcelain tile outdoors outperforms almost anything else on the market. Miss on any one of them, and the first wet winter finds every weak spot.

Why Porcelain Handles the Outdoors: Frost, Water, and Density

Porcelain starts as a dense clay body fired well above 1,200°C. That high firing temperature is what separates it from ceramic. Water absorption drops under 0.5% in a properly rated outdoor porcelain tile, and that number carries more weight than any marketing line on the box.

Here is why it matters in this climate. Rain works into a porous tile, sits in the pores through a cold December night, then freezes before morning. Ice expands. The tile cracks from the inside, usually along a hairline nobody notices until spring. Porcelain with sub-0.5% absorption never lets that water in to begin with. Frost resistance, stain resistance, scratch resistance: the same dense body delivers all three, and it is why porcelain tile outdoors has become the default recommendation over natural stone on most jobs we quote.

Can I Use Indoor Porcelain Tiles Outside?

Short answer: no, not the way most people mean it. This question comes up on almost every consultation involving leftover tile from a kitchen or bathroom job. The instinct makes sense. Same material, why not save the money.

Indoor porcelain runs thinner, usually around 10mm, built for foot traffic on a stable subfloor indoors. Outdoor-rated porcelain runs 20mm to 30mm, engineered to carry point loads, resist frost cycling, and sit over a pedestal or compacted base without cracking. Slip rating is the other gap. Indoor tile is tested and certified for indoor coefficient of friction, which is a lower bar than what an exterior surface needs in the rain or under a garden hose. Reuse indoor stock outside and the tile that survived five years in a hallway can fail its first winter on a patio.

One exception worth naming: some manufacturers sell a matched indoor/outdoor line at the thicker gauge specifically so a kitchen floor and a patio can share one look through a set of patio doors. That is a deliberate outdoor-rated product wearing an indoor finish, not the leftover box from the last reno.

Slip Resistance: The Rating That Actually Matters Outside

A polished, glossy finish belongs indoors and nowhere else. Rain, sprinkler overspray, melting snow: an outdoor surface is wet often enough that slip resistance stops being optional. Look for a coefficient of friction rating built for exterior use, typically the higher end of the R-scale, well above what a bathroom floor requires. Textured and matte finishes carry that rating more consistently than anything glazed.

Around a pool or hot tub this stops being a style preference and becomes the actual safety spec. We steer clients away from anything glossy within arm’s reach of standing water, full stop.

Where Outdoor Porcelain Tile Holds Up

Patios, pool decks, walkways, and driveways: outdoor porcelain tile covers all four when the gauge and rating match the application. Thinner 20mm product suits patios and walkways under foot traffic. Driveways and any area seeing vehicle weight need the 30mm range, installed over a proper compacted base.

Terraces and rooftop decks over pedestals are where outdoor porcelain has really taken off the last several years. The pedestal system keeps the tile consistent in height even over an uneven substrate, and it leaves a drainage gap underneath that a mortar-set installation cannot match. Commercial patios and hotel courtyards use the same approach for the same reason: even wear, fast drainage, minimal long-term maintenance.

What Goes Under Outdoor Porcelain Tile

Two installation methods cover most residential jobs. A pedestal system raises the tile above the ground, allows water to drain freely underneath, and makes individual tiles liftable for utility access. Compacted gravel or concrete with proper mortar and a drainage slope works too, and it is the more familiar method for a patio that sits at grade rather than up on a deck or balcony.

What does not work: laying outdoor porcelain directly on bare soil, or skipping the drainage slope because the patio “looks flat enough.” Standing water finds every low spot within a season, and that is where staining and freeze damage start even on a correctly rated tile. Get in touch before the material’s ordered. That’s the cheapest moment to change your mind.

Frequently Asked Questions

What are the disadvantages of porcelain tiles outside?

Cost and installation skill, mainly. Outdoor-rated porcelain runs more than concrete pavers per square foot, and cutting the thicker 20-30mm gauge needs a wet saw rated for the material. Colour and texture options also run narrower than indoor lines, since fewer manufacturers make the outdoor-rated version.

Can any porcelain tile be used outside?

No. Only tile rated and tested for exterior use: sub-0.5% water absorption, the thicker 20-30mm gauge, and a slip rating built for wet conditions. A tile box without those specs printed on it should stay indoors.

What happens if porcelain tile gets wet?

Nothing, on a properly rated outdoor tile. The dense, low-absorption body sheds water instead of soaking it in, which is the entire point of the material for an Island application that sees rain, runoff, and sprinkler spray for eight months of the year.

What do you put under porcelain tile outside?

A pedestal system for raised patios and decks, or a compacted gravel/concrete base with mortar and a drainage slope for a ground-level patio. Bare soil is never the answer, regardless of how the tile is rated.

Will porcelain tile crack outside?

Properly rated outdoor porcelain, installed on the right base with the right expansion joints, holds up through repeated frost cycling. Cracking almost always traces back to indoor-grade tile pressed into outdoor service, a missing drainage slope, or a base that was never compacted.

Will porcelain tile hold up outside?

Years, often decades, with almost no maintenance beyond a seasonal rinse. That durability is the reason outdoor porcelain has taken over so much of the patio and pool-deck market from natural stone and concrete pavers over the last decade.

Sourcing the right gauge and rating is most of the job before a single tile gets cut. Jordan Tile & Stone handles porcelain installation from material selection through the finished patio, indoors or out.

Related Questions

• Are Porcelain Tiles Good for Outdoors?
• What Color Grout to Use with White Tile?
• Can Foam Tiles Be Used Outdoors?
• Are Big Tiles Better in a Small Bathroom?
• What Color Goes with Grey Tiles?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Are Tiles Eco-Friendly?

Mostly, yes, more than the flooring aisle gives it credit for. Fired clay, stone, and recycled glass sit closer to the low-impact end of the flooring spectrum than vinyl, laminate, or a lot of engineered wood. That answer changes once you factor in where the tile was made, what went underneath it, and how long it actually lasts on the floor.

We get this question from a specific kind of homeowner. Someone renovating a bathroom, wanting the durability of tile without feeling like they are choosing the worse option for the planet. The short version: tile itself is a genuinely low-impact material. Recycled content, the setting materials underneath it, and whether the install lasts fifteen years or gets ripped out again in three, that is what actually makes or breaks the eco case.

What Actually Makes an Eco-Friendly Tile

Raw materials, first. Clay, sand, and stone are abundant and fired at temperatures far lower than metal or glass manufacturing needs. Recycled content is the bigger lever, though. Porcelain and ceramic bodies increasingly include post-consumer glass or reclaimed ceramic waste, and some glass tile lines run close to 100% recycled glass, bottles and jars diverted straight out of the recycling stream.

Lifespan matters just as much as what the tile is made from. A properly installed tile floor runs decades, not years. Vinyl and laminate get replaced on a much shorter cycle, and every replacement is another trip to the landfill. Fewer replacement cycles, less total material used over the life of a home, that math favours tile even before recycled content enters the picture.

Certifications like EPDs (Environmental Product Declarations) and LEED credits exist for exactly this comparison. Useful for an architect specifying a commercial project. Less useful for a homeowner standing in a showroom trying to decide between two similar-looking porcelain lines. The advice that actually helps there: ask the supplier for the recycled-content percentage directly, in writing if they have it.

What Is the Most Eco-Friendly Tile?

Recycled glass tile tops most lists, and for good reason. High post-consumer content, striking colour range, genuinely low-impact production. It works well as an accent or backsplash but costs more per square foot than porcelain and needs a skilled hand to cut cleanly.

Porcelain with a high recycled-content rating is the more practical daily-driver answer. Dense, low water absorption, rated for decades of wear in wet areas. For an Island bathroom or kitchen, durability itself is part of the eco argument: a porcelain floor holding up for twenty-five years beats a “greener” material that needs replacing twice in that same span.

Reclaimed and salvaged tile deserves a mention too, pulled from renovations or demolitions rather than manufactured new. Harder to source in matching quantities, but the lowest-impact option that exists, since nothing new gets fired at all.

Does Porcelain Tile Emit VOCs?

No, not the tile itself. Fired porcelain is an inert ceramic body, no off-gassing once it comes out of the kiln. The VOC concern homeowners actually run into comes from what goes underneath and around the tile, not the tile.

Thinset, mastic adhesives, and some grout sealers are where volatile organic compounds show up. Cheaper mastic-style adhesives and solvent-based grout sealers carry noticeably more VOCs than a modern water-based thinset or sealer. Ask specifically for low-VOC setting materials on a bathroom or bedroom job, and the whole installation ends up close to VOC-free, tile included.

What Is the Most Environmentally Friendly Flooring?

Tile ranks near the top of any real comparison, alongside cork and natural linoleum. Vinyl plank looks appealing on price and installs fast, but it is petroleum-based, does not biodegrade, and typically lasts ten to fifteen years before it gets torn out and landfilled. Carpet performs worse still, trapping allergens and needing full replacement every seven to ten years in a busy household.

Natural linoleum, made from linseed oil and cork dust rather than vinyl’s PVC, comes close to tile on the low-impact scale and costs less. It scratches more easily and needs resealing every few years, a trade-off tile does not carry.

Tile’s one real weak spot on this comparison is transport. A porcelain slab shipped from overseas carries a shipping footprint that a regionally produced product does not. Worth asking a supplier where a given line is actually manufactured, not just where it is sold from, before assuming imported automatically means less sustainable than it looks on paper.

Should You Have Tiles in the Living Room?

Tile works fine in a living room, and on the Island the usual objection, cold underfoot, matters less than it does inland. Winters here stay mild and damp rather than deep-frozen, so a tile floor loses its chill faster once the heat kicks on than the same floor would in a Prairie winter. A rug in the main seating area and a decent area heat source cover most of the comfort gap.

In-floor radiant heat under tile solves the temperature issue completely and pairs well with our climate, since the damp months are exactly when a warm floor gets noticed most. For a living room that opens onto a patio or gets heavy foot traffic from kids and dogs, tile’s durability and easy cleanup often win out over the warmer feel of engineered hardwood.

The Part Most Eco-Tile Guides Skip: The Old Tile Coming Out

Every article about eco-friendly tile talks about what goes in. Almost none mention what comes out. A re-tile job usually means tearing out a floor that still has plenty of structural life left in it, and that demolition waste is the biggest environmental cost most homeowners never think about.

A clean, correctly bonded original install makes that tear-out easier and produces less rubble to haul away. Overbuilt thinset beds, multiple layers of tile stacked on top of each other from past renovations, that is where a demo job turns into a dumpster full of debris instead of a manageable haul. Ask your installer what happens to the old material before the new floor goes down. Some of it, broken tile especially, can go into aggregate or road base rather than a landfill, depending on what the local waste facility accepts.

Grout is the other overlooked piece. Old grout ground out during a re-tile is mostly cement dust, low environmental cost on its own, but a full grout haircut across a large floor still adds up in disposal weight. Regrouting instead of a full tear-out, when the tile underneath is still sound, keeps that whole layer out of the bin entirely and costs a fraction of a new install.

Buying Eco-Friendly Tile for a Vancouver Island Home

A short checklist, from 35 years of fielding this exact question on the tools:

Recycled content percentage, ask the supplier directly rather than trusting a green-sounding product name. Porcelain over ceramic for wet areas, since durability reduces waste over a floor’s full lifespan. Low-VOC thinset and grout, especially for a bedroom or main living space. Buy close to the actual square footage needed, with a modest overage for cuts and future repairs, rather than a large buffer that ends up as offcuts in a bin.

Weighing recycled-content porcelain against a reclaimed option, or trying to figure out how much material a room actually needs before ordering, Jordan Tile & Stone serves Campbell River, Courtenay, Comox, Oyster Bay, and the rest of central Vancouver Island with straight advice before the order gets placed. Floor jobs, wet-area jobs, we handle the full floor tile installation from planning through cleanup. Get in touch and we will walk through what actually fits the space and the budget.

Related Questions

• Are Peel and Stick Backsplash Tiles Removable?
• Can You White Wash Tile?
• Do You Use a Hammer Drill for Tile?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8

Can You Tile Over Brick? What Actually Holds and What Doesn’t

Yes, most of the time. Brick gives tile something to grip onto once it’s prepped right, and ripping out a solid brick fireplace or accent wall just to start over is usually more demolition than the job needs. The catch isn’t whether brick can be tiled over. It’s whether that particular brick is in good enough shape to trust with fifty pounds of new tile hanging off it.

Can You Put Tile Directly on Brick?

Directly, no. Not with any adhesive straight out of the bucket. Brick and mortar joints are uneven, porous in some spots and sealed in others, and that inconsistency is exactly what makes tile adhesive fail early. What actually happens on a real job: the masonry gets cleaned, any loose material gets knocked off, and then a bonding layer goes down before tile ever touches it.

That bonding layer is usually thinset mortar, sometimes with a primer first if the brick is painted or unusually smooth. Skip that step and the tile might hold for a season. Then a grout line cracks, or a corner tile pops loose, and the whole thing has to come off anyway. Prep once, properly, and it’s a permanent surface.

What to Check Before You Tile Over Brick

Loose mortar joints are the first red flag. Run a putty knife along a few joints. Crumbles and falls out easily, that’s a problem no amount of thinset fixes. Repoint it first or the tile has nothing solid underneath to key into.

Efflorescence is the second thing worth a look, that white chalky residue that shows up on masonry exposed to moisture over time. It means water has been moving through that wall at some point. Tile over an active moisture problem and the water doesn’t go away, it just gets trapped behind new tile where nobody sees it until the grout starts staining or the tile starts sounding hollow when tapped.

Structural movement matters too. A brick fireplace surround that’s been there since the house was built and hasn’t shifted is a straightforward job. A brick wall with a visible crack running through several courses needs that crack addressed first, because tile doesn’t flex and will telegraph that same crack right through the grout line within a year.

What Material Actually Goes Over Brick?

Thinset mortar does almost all the work. Modified thinset specifically, the kind with polymer additives that grip better to a porous or uneven surface than standard unmodified mortar. On masonry that’s rough or heavily textured, that grip matters more than on a flat, smooth substrate.

A bonding primer goes on first in two situations: painted brick, or brick that’s unusually dense and glazed-looking. Primer gives the thinset something to grab. Skip it on painted brick specifically and thinset can bond fine to the paint while the paint itself is barely holding to the brick underneath, which means the whole assembly, paint and tile together, eventually lets go.

Cement backer board is the third option, and it’s the one we reach for when the masonry surface is too rough, too uneven, or has too many proud joints to tile over directly. Screw the backer board straight into the mortar joints with masonry screws, and now the tile is going onto a flat, predictable surface instead of fighting brick’s natural texture.

Fireplace Hearth or Brick Wall: Does It Change Anything?

Vertical brick, like a fireplace surround or an accent wall, only has to hold the tile’s own weight against gravity working sideways, not down. A horizontal hearth floor is a different load case entirely. Every dropped log, every foot stepping across it, pushes straight down onto that bond.

Heat matters on a hearth and firebox surround in a way it never does on a plain wall. Standard ceramic can handle normal fireplace heat fine at a reasonable distance from the firebox opening, but tile going right up against or above an active firebox needs a rating built for it, and local building code usually sets a minimum clearance regardless of tile choice. Worth confirming that clearance before tile ever gets ordered, not after.

Wall tile has more room for error. A dropped item on a hearth floor is a much harder hit than anything a wall surface takes, which is part of why porcelain shows up more often on hearths and ceramic still does fine on the surround above it.

Can You Tile Over Existing Painted Brick?

Yes, with one extra step most homeowners skip and regret. Paint on brick is its own bonding problem, separate from the masonry underneath. Thinset needs to grip the paint layer, and the paint layer needs to still be gripping the brick, and if either link in that chain is weak the tile eventually goes with it.

Test it first. A strip of painter’s tape pressed firmly onto the painted brick and pulled off tells you fast whether that paint is holding on or already failing. Peeling, flaking, or chalky paint needs to come off before anything else happens, either scraped back to bare brick or hit with a bonding primer rated for glossy or painted masonry. Solid paint that passes the tape test just needs a light scuff-sand and a primer coat before thinset goes on.

Will Peel-and-Stick Tile Stick to Brick?

Not reliably, and it’s worth saying plainly because it’s the question that comes up most from anyone trying to avoid a full tile job. Peel-and-stick relies on a flat, smooth surface for its adhesive backing to grip evenly across the whole tile. A masonry face offers no such thing. Mortar joints sit recessed below the brick face, individual bricks vary in texture, and the peel-and-stick backing only makes real contact at the high points.

The result is tile that looks fine for a few weeks and then starts lifting at the corners and edges, right where the mortar joints sit underneath. It’s not a workmanship problem at that point, it’s the product meeting a surface it was never built for. A textured skim coat or backer board over the brick first can get a flat enough surface for peel-and-stick to actually work, but at that point the extra step has already closed most of the time savings peel-and-stick was supposed to offer.

Vancouver Island Considerations

Coastal humidity slows thinset cure time more than most homeowners expect, especially through the wetter months. A cure that takes a day inland can run closer to two here, and grouting too early on this kind of job traps moisture that’s still working its way out of the mortar joints underneath. Give it the extra day before grouting, particularly on an exterior-facing wall or a fireplace that backs onto an uninsulated chimney chase.

Older homes across Campbell River, Courtenay, and Nanaimo often have brick fireplaces original to the build, and the mortar on those has usually had decades to soften or start failing at the joints. That’s the first thing we check on a quote, before quoting a tile material at all.

When to Call a Pro Instead of DIYing It

A small, solid, unpainted brick surround with no visible movement is a reasonable weekend project for a confident DIYer. Add in painted brick, any sign of moisture, a hearth floor that needs a heat-rated tile, or a fireplace with active gas or wood-burning use, and the margin for error narrows fast. A bad bond on a wall is an annoyance. A bad bond a foot from an active firebox is a different kind of problem.

Our wall tile installation work covers exactly this kind of brick fireplace surround and accent wall job, prep included, and our floor tile installation crew handles hearth floors where heat rating and impact resistance both need to be right the first time. Not sure which way your own job should go? Ask us and you’ll get a straight answer instead of a range.

Frequently Asked Questions

Can you put tile directly on brick?

Not without prep. Clean the brick, address any loose mortar, then bond with modified thinset or backer board first. Skipping straight to adhesive-and-tile is the shortcut that fails within a year.

What material can you put over brick?

Modified thinset mortar handles most jobs directly. Painted or glazed brick needs a bonding primer first. Rough or badly uneven brick often does better with cement backer board screwed into the joints, giving tile a flat surface instead of brick’s natural texture.

Can you tile over existing brick?

Yes, as long as the mortar joints are solid and there’s no active moisture behind it. Painted brick needs a tape test first to confirm the paint itself is still bonded before tile goes anywhere near it.

Will peel and stick tile stick to brick?

Not on its own. The recessed mortar joints and uneven brick face leave peel-and-stick backing with only partial contact, and it lifts at the edges within weeks. A flat skim coat or backer board first fixes that, but it adds back most of the time peel-and-stick was meant to save.

Brick holds tile fine once it’s treated like the substrate it actually is, not like drywall with a rougher finish. Check the mortar, face up to failing paint instead of tiling straight over it, and match the tile rating to whether it’s a wall or a hearth taking the load. Most brick fireplace jobs on the Island come down to that prep step more than anything about the tile itself.

Related Questions

• Can I Tile Over Wallpaper?
• Is Vinyl Tile Durable?
• Can You Epoxy Over Tile?
• Can I Tile Over Redgard?
• Are Leave-In Tile Spacers Good?

Jordan Tile & Stone

Tile installation and repair across central Vancouver Island: Campbell River, Courtenay, Comox, Oyster Bay, Nanoose Bay, Parksville, Qualicum Beach and Nanaimo.

Phone: (250) 201-3891
Hours: Monday to Sunday, 7:00 am to 6:00 pm
Address: 4423 Patricia Rd, Oyster Bay, BC V9H 1B8